| |
Applications
The iCLASS RK40 read only contactless smart card
reader with keypad.
Using 13.56 MHz contactless smart card technology, the iCLASS RK40 provide a powerful solution. Combine a contactless card
presentation with a personal identification number (PIN) to support dual authentication
of identity. Or, configure the panel for single-factor authentication, using
only a card or a PIN.
The PIN can be verified either at the access control panel or locally by
the keypad reader. When verified locally, the PIN must be programmed into the iCLASS card.
Read/write applications
include the storage/retrieval of data such as biometric templates, health records, time and attendance, and digital
cash. The possibilities are endless!
|
| |
Featuring crisp architectural styling, the keypad reader and reader/writer
have an elegantly curved faceplate. The 12-position weatherproof keypad uses discrete switches to
provide positive tactile response, optionally reinforced by an audible tone. The keypad also
features a waterproof silicone rubber boot, vandal-resistant metal keycaps, and backlit numbering. The units are equipped with a Wiegand output that easily interfaces with
most existing access control panels.
The iCLASS RK40 is compatible with
all iCLASS credentials. The units can read or read/write to credentials compatible with several ISO standards:
Features
• Data Output Formats: The keypad reader reads standard proximity format data from HID iCLASS cards, and will output data as encoded. When reading MIFARE® cards, the keypad reader can be configured
to output 26 bit, 32 bit, 34 bit, or 40 bit Wiegand formats based on the card serial number.
Wiegand keypad data format can be configured for transmission of
individual key presses as ASCII encoded Hex digits, or for buffering and transmission of the PIN as a card
number in SIA 26 bit format with a configurable facility code.
Additionally, the RWK400 offers a bi-directional serial port that
communicates at data rates up to 57.6 Kbaud. Using the ISO 7816 protocol, the standard for contact smart card
applications, the RWK400 allows connection to a PC or microcontroller to support read/write applications.
• Keypad: Twelve discrete switches are covered with a silicone rubber boot and
vandal resistant metal keycaps. Raised tactile mark on "5" key for visually impaired users.
Configurable audio feedback.Backlit
numbers in bezel overlay, above each key. Lighting is configurable: "Always
On", "Always Off", "Triggered by Card Read", or "Triggered by Key Press".
• Security: 64 bit authentication keys are extremely secure. Readers and cards require
matching keys to function. All RF data transmission between the card and keypad reader is encrypted,
using a secure algorithm. The key management system reduces the risk of compromised or duplicated cards.
Cards and keypad readers with site-specific keys are optionally available
from the factory.
Alternatively, the iCLASS CP400 Field Programmer® can be used
to create site-specific keys. The programmer also allows users to create a keypad reader configuration card, which is used
to re-key cards and keypad readers on site.
• Programming/Configuration: All cards are shipped with unique diversified keys; keypad readers are
shipped with compatible keys. All keys are derived from the HID Standard key. While cards and keypad readers
with Standard keys are interchangeable, the keys are highly secure. Further enhance security by
ordering with iCLASS Elite formatting.
• Audiovisual Indication: Audio transducer provides configurable tone sequences to signify access
granted, access denied, power up, and configuration card read. A light bar provides a clear visual
status indication in red, green, or amber.
• Open Collector Output (RWK400 Only): Normally Open logic output, controlled via serial port. Switches up to
50mA at 12 VDC. Use interposing relay for larger loads. Configurable to latch momentarily upon
successful local verification of PIN stored on the card.
• Mounting: Mounting plate attaches to U.S./ EU/ Asian back box, 52-60 mm screw hole
spacing (vertical or horizontal). Keypad reader housing latches onto mounting plate, secured
with a screw. Mounts on metal with minimal read range impact. An optional spacer can be used for surface
mount installations.
• Indoor/Outdoor Design: Rugged, weatherized polycarbonate enclosure designed to withstand harsh
environments provides reliable performance and resistance to vandalism. Permanent magnet built
into housing facilitates tamper alarm when used with a magnetic reed switch.
• Warranty: Warranted against defects in materials and workmanship for life. (See
complete warranty policy for details)
• Base Part Numbers
• RK40 Read Only Keypad: 6130
• RWK400 Reader/Writer Keypad: 6131
• Options
• Color - Black, Gray
• Key Management - Standard or High Security
• Selectable Output Type (for MIFARE cards)
• Termination - removable connector with miniature screw terminals or
18" (45.72 cm) wire pigtail.
• Programmable LED/Beeper operation
• Accessory - Security Tool; 04-0001-03
Specifications
• Dimensions: 3.30" x 4.80" x 0.9" (8.38 cm x 12.19 cm x 2.286 cm)
• Material: UL94 Polycarbonate
• Power Supply: 10 - 16 VDC reverse voltage protected / Linear supply recommended
• Current Requirements (Avg/Peak): 72/244 mA @ 12 VDC
• Operating Temperature: -31° to 150° F (-35° to 65° C)
• Operating Humidity: 5% to 95% relative humidity non-condensing
• Weight: Approximately 10 oz (283.49 g)
• Transmit Frequency: 13.56 MHz
• Cable Distance:
• Wiegand Interface - 500 feet (150 m); RS-232 - 50 feet (15 m); RS-485 - 4000 feet (1220 m)
• Recommended cable is ALPHA 1299 (22AWG)
Specifications
• iCLASS Card - 3.0-4.0" (7.6-10.1 cm)
• iCLASS Key - 1.0-1.5" (2.5-3.8 cm)
• iCLASS Tag - 1.0-1.5" (2.5-3.8 cm)
• iCLASS Prox - 1.5-2.5" (3.8-6.3 cm)
• MIFARE Card (serial number only) - 1-2" (2.5-5.0 cm)
Donwload
• Catalog
• How to Order Guide
|
